Back to Network
7
Shared Docs
7
Same-Page
8 / 7
Mentions
Document Mentions (7 shared documents)
3 mentions1 same-page
Page ?Same page
the valve, and it responding. The pressure supplied =s closing the valve, and maintaining the 400 Degrees requested. No voltage equals no p=essure, Valve open, lowering the Temperature. 4 EFTA_R1_01332993 EFTA02352918 The right side shows g=ving a close signal to the precooler (fan air) valve. Hi
_R1_01332993 EFTA02352918 The right side shows g=ving a close signal to the precooler (fan air) valve. High Voltage, and pres=ure supplied to the Valve on that side to close, and increase the temperat=re. That side doesn't seem=to respond. The valve has a 4 inch=input/output side. The control line
ning manuals s=ow that the system is up to 14 VDC, it goes through a resistor and is a 10=VDC Maximum to the torque motor. Remember that the box=in the Radio Rack is an add-on, it is not normally installed, and there ar= no requirements for calibration- The 9 volts seems to =e appropriate for the full close si
2 mentions1 same-page
Page ?Same page
, lowering the Temperature. The right side shows giving a close signal to the precooler (fan air) valve. High Voltage, and pressure supplied to the Valve on that side to close, and increase the temperature. That side doesn't seem to respond. The valve has a 4 inch input/output side. The control line
ning manuals show that the system is up to 14 VDC, it goes through a resistor and is a 10 VDC Maximum to the torque motor. Remember that the box in the Radio Rack is an add-on, it is not normally installed, and there are no requirements for calibration- The 9 volts seems to be appropriate for the full close si
2 mentions1 same-page
Page ?Same page
, lowering the Temperature. The right side shows giving a close signal to the precooler (fan air) valve. High Voltage, and pressure supplied to the Valve on that side to close, and increase the temperature. That side doesn't seem to respond. The valve has a 4 inch input/output side. The control line
ning manuals show that the system is up to 14 VDC, it goes through a resistor and is a 10 VDC Maximum to the torque motor. Remember that the box in the Radio Rack is an add-on, it is not normally installed, and there are no requirements for calibration- The 9 volts seems to be appropriate for the full close si
Sponsored
2 mentions1 same-page
Page ?Same page
, lowering the Temperature. The right side shows gi=ing a close signal to the precooler (fan air) valve. High Voltage, and press=re supplied to the Valve on that side to close, and increase the temperatu=e. That side doesn't s=em to respond. The valve has a 4 inch =nput/output side. The control line
ning manuals s=ow that the system is up to 14 VDC, it goes through a resistor and is a 10=VDC Maximum to the torque motor. Remember that the box=in the Radio Rack is an add-on, it is not normally installed, and there ar= no requirements for calibration- The 9 volts seems to =e appropriate for the full close si
2 mentions1 same-page
Page ?Same page
, lowering the Temperature. The right side shows gi=ing a close signal to the precooler (fan air) valve. High Voltage, and press=re supplied to the Valve on that side to close, and increase the temperature. That side doesn't s=em to respond. The valve has a 4 inch =nput/output side. The control line
ning manuals s=ow that the system is up to 14 VDC, it goes through a resistor and is a 10=VDC Maximum to the torque motor. Remember that the box=in the Radio Rack is an add-on, it is not normally installed, and there ar= no requirements for calibration- The 9 volts seems to =e appropriate for the full close si
2 mentions1 same-page
Page ?Same page
, lowering the Temperature. The right side shows gi=ing a close signal to the precooler (fan air) valve. High Voltage, and press=re supplied to the Valve on that side to close, and increase the temperatu=e. That side doesn't s=em to respond. The valve has a 4 inch =nput/output side. The control line
ning manuals s=ow that the system is up to 14 VDC, it goes through a resistor and is a 10=VDC Maximum to the torque motor. Remember that the box=in the Radio Rack is an add-on, it is not normally installed, and there ar= no requirements for calibration- The 9 volts seems to =e appropriate for the full close si
Sponsored
2 mentions1 same-page
Page ?Same page
, lowering the Temperature. The right side shows gi=ing a close signal to the precooler (fan air) valve. High Voltage, and press=re supplied to the Valve on that side to close, and increase the temperatu=e. That side doesn't s=em to respond. The valve has a 4 inch =nput/output side. The control line
ning manuals s=ow that the system is up to 14 VDC, it goes through a resistor and is a 10=VDC Maximum to the torque motor. Remember that the box=in the Radio Rack is an add-on, it is not normally installed, and there ar= no requirements for calibration- The 9 volts seems to =e appropriate for the full close si
Sponsored
Mutual Connections (11)
Entities connected to both Valve and the Radio Rack
Jeffrey Epstein
PERSON16 w/ Valve·8 w/ the
LV
Larry Visoski
PERSON14 w/ Valve·8 w/ the
Anticipator
LOCATION7 w/ Valve·7 w/ the
The LP air
ORGANIZATION7 w/ Valve·7 w/ the
PR
Pete Rawson
PERSON7 w/ Valve·6 w/ the
VDC Maximum
ORGANIZATION5 w/ Valve·5 w/ the
AN
Anticipators
PERSON7 w/ Valve·2 w/ the
WH
Wing heat
PERSON6 w/ Valve·2 w/ the
the Controller (ie
ORGANIZATION4 w/ Valve·4 w/ the
No Voltage
LOCATION2 w/ Valve·2 w/ the
the Controller (ie the Computer
ORGANIZATION2 w/ Valve·2 w/ the